• Complimentary shipping on orders above $800. Prices are inclusive of GST*
UniFi UA-SK-Elevator (Protect Access Reader Elevator Starter Kit up to 18 Floors)

    UniFi UA-SK-Elevator (Protect Access Reader Elevator Starter Kit up to 18 Floors)

    $1,550.00
    Tax included. Shipping calculated at checkout.
    Connects to in-elevator readers using PoE to authorize user's floor selection. Support for up to 18 floors and digital inputs for car status and emergency.

    (1) Elevator Hub

    (1) G2 Reader

    (2) 2-wire PoE extenders

    (10) Access Cards

     

    Access Elevator Starter Kit

    Access Elevator Starter Kit

    Access Elevator Starter Kit

     

    Technical Specifications

    UA-Hub-Elevator
    Mechanical
    Dimensions 129.3 x 244.7 x 33.6 mm (5.1 x 9.6 x 1.3")
    Weight 537 g (1.2 lb)
    Enclosure material Polycarbonate
    Mounting material Polycarbonate
    Hardware
    Networking interface (4) 10/100/1000 Base-T
    Management interface (1) 10/100/1000 Base-T
    Power method PoE++
    Max. power consumption 7W (Without PoE output)
    PoE input (1) PoE++, 50V DC, 1.2A
    PoE output PoE passthrough, (4) PoE, 50V DC, total 42W
    ESD/EMP protection Air: ±8kV, contact: ±4kV
    Digital input (5) Car position
    (6) Car status; Up/down/stop/full/door open/door close
    (1) Emergency
    Outputs (18) Relays
    Rating 30V DC/2A
    LEDs System: white/blue/red
    Output relays: white
    Buttons (1) Factory-reset
    Terminal blocks
    Ambient operating temperature -10 to 40° C (14 to 104° F)
    Ambient operating humidity 5 to 95% noncondensing
    Certifications CE, FCC, IC
    UACC-Extender-2Wire-Tx/Rx
    Mechanical
    Dimensions 40 x 105 x 25 mm (1.6 x 4.1 x 1")
    Weight PoE in: 77 g (2.7 oz)
    PoE out: 79 g (2.8 oz)
    Enclosure material Polycarbonate
    Mounting material Polycarbonate
    Hardware
    Networking interface (1) 10/100 MbE
    (1) Homeplug AV
    Management interface (1) 10/100 MbE
    Power method PoE++
    Max. power consumption 3W (Without PoE output)
    PoE input (1) PoE++, 50V DC, Max. 1.2A
    PoE output (1) PoE+, 48V DC, 0.72A
    ESD/EMP protection Air: ±8kV, contact: ±4kV
    LED White
    Ambient operating temperature -10 to 40° C (14 to 104° F)
    Ambient operating humidity 5 to 95% noncondensing
    Certifications CE, FCC, IC
    UA-G2
    Mechanical
    Dimensions 93 x 40 x 36.5 mm (3.7 x 1.6 x 1.4")
    Weight 82 g (2.9 oz)
    Enclosure material Polycarbonate, glass
    Mounting In wall, gang box
    Weatherproofing IP55
    Hardware
    Networking interface (1) 10/100 MbE RJ45 port
    Connectivity BLE 4.1
    Power method PoE
    UL 294 Power-limited Class 2 PSU
    UL 60950-1/62368-1 LPS/PS2 PSU
    Supported voltage range 48V DC
    Max. power consumption 5W
    ESD/EMP protection Air: ±15kV, contact: ±8kV
    Sensors Proximity sensor
    Speaker (1) 8 ohm, 0.7W
    LEDs R/G/B/W
    Button (1) Factory-reset
    NFC frequency 13.56 MHz
    NFC read range < 30 mm
    NFC standards ISO 14443A, 14443B, 15693
    NFC technology NFC Tag 1,2,3,4,5
    MIFARE Classic
    MIFAREPlus
    MIFARE Ultralight
    MIFARE DESFire
    Operating environment Outdoor use
    Ambient operating temperature -30 to 45° C (-22 to 113° F)
    Ambient operating humidity 5 to 90% noncondensing
    Software information The software version of a product can be checked at https://unifi.ui.com
    UL 294 level Destructive attack: Level I
    Line security: Level I
    Endurance: Level I
    Standby power: Level I
    UL 294 statement Compliance with IEEE 802.3 specifications was not verified as part of UL 294.
    The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
    PoE cabling requirements Cable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site.
    The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm2) for patch cords; 24 AWG (0.21 mm2) for horizontal or riser cable.
    CAN/ULC-60839-11-1 Grade Grade assignment: I
    Certifications CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
    Document number, and issue date and/or revision level UA-G2/UA-G2-Black, V02
    LED
    System Steady blue: Adopted/device is ready
    Steady white: Pending adoption
    Blinking white/blue: Upgrading firmware
    Strobing red: Emergency lockdown
    UA-Card
    Mechanical
    Dimensions 85.6 x 54 x 0.8 mm (3.4 x 2.1 x 0.03")
    Weight 5 g (0.18 oz)
    Format ISO 7810 ID-1
    NFC frequency 13.56 MHz
    NFC technology ISO/IEC 14443 Type A
    MIFARE DESFire
    UniFi Access Proprietary Security Protocol

    RELATED PRODUCTS

    BACK TO TOP